Need service? Call:972-681-2222 

Programming your HomeLink® Remote

Caution! Before activating the door, be sure that all people, pets, ladders, vehicles and other obstructions are cleared from the door’s path.

Note! Some vehicles may require the ignition to be turned on or to the second (or "accessory") position for programming and/or operation of HomeLink. It is also recommended that a new battery be replaced in the hand held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio frequency. Please use a ladder and do not stand on your vehicle during the programming steps for a rolling code opener.

Rolling Code Programming: 
1. Press and hold the two outer HomeLink buttons until the indicator light begins to flash (after 20 seconds). Do not hold for longer than 30 seconds. Do not repeat this step to program additional HomeLink buttons. 

2. Place the hand-held remote 1-3 inches from the HomeLink button you want to program. 

3. Simultaneously, press and hold both the HomeLink and hand-held remote buttons. Do not release either button until step 4 has been completed. (If you reside in Canada, refer to the "NOTE" below.) 

4. When the indicator light changes from a slow blink to a rapid flash, release both buttons. 

5. At the garage door opener receiver (motorhead unit) in the garage, locate the"learn" or "smart" button (usually near where the hanging antenna wire is attached). 

6. Press and release this "learn" or "smart" button. (The name of these buttons vary by manufacturer.) There are 30 seconds in which to initiate step 7. 

7. Firmly press, hold for two seconds, and release the programmed HomeLink button. Do this procedure again and, depending on the make of your garage door opener, do this procedure a third time to complete the procedure. 

The garage should now activate when the programmed HomeLink button is firmly pressed and released. If not, give us a call or refer to the "Troubleshooting Tips" noted below. 
Troubleshooting Tips: 

** Check the frequency of the garage door opener's hand-held remote (usually found on the back). HomeLink is compatible with radio-frequency devices operating between 288-399 Mhz. 

** Put a brand new, store bought battery in the hand held remote. During the programming process (step three above) the battery's energy tends to drain (more so with an older battery). A new battery will increase the speed and accuracy in which the hand-held remote sends its signal to HomeLink. 

** Retrain HomeLink holding the hand-held remote at different lengths and angles from the HomeLink button you are trying to program (during programming step three). Try 4-6 inches away at a different angle. 

** Confirm that the HomeLink button you are trying to program is in the "programming mode". Press and hold the desired button. The indicator light will be a slow blink when HomeLink is in the "programming" mode and can be programmed at any time. 
Verifying HomeLink has picked up a rolling code signal: 

** Press and hold the programmed HomeLink button. If the indicator light blinks rapidly for two seconds and turns solid, HomeLink has successfully picked up the rolling code signal. If necessary, proceed with steps 5-7 noted above to complete the rolling code programming. 
If this does not work, please call our customer service center for further assistance at the number above. We can come out to you location and do the job for you.

These are general HomeLink instructions that apply to most vehicles. For more specific instructions tailored for your specific make and model please visit the HomeLink site here!

Having Trouble Programming Your Homelink Remotes?

We Will Come To Your House and Program it For You!

 
JeffV.jpg

Toll Free 24/7
1-800-269-9403

Dallas County
972 - 681 - 2222
------------------------------
North Dallas
972 - 335 - 5885
------------------------------
Tarrant County
817 - 496 - 3000

accepted cards

BBB A+

 Visit our facebook page here!

Copyright 2011 American Service Center - Dallas/Fort Worth's premier source for garage door installation and repair! Design by Matt Lozoya. Increase your website traffic with Attracta.com